Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Pbxsummary
Supportfiles1Avaya Meridian.TDT
Supportfiles2Avaya Meridian.TDS
ConnectionSerial connection
RequiredTask1Configure the SMDR output
RequiredTask2Install NetPBX
RequiredTask3Configure TIM Enterprise

HTML
<a >

 

Configuring your SMDR

By default, the SMDR output in the Avaya Meridian Option Series is disabled. You need to speak to your system maintainer to have this enabled for incoming, outgoing and internal calls. Additionally, CLI, DNIS, response time and abandoned calls should be enabled for incoming calls.

You need to configure one of the  TTY ports on the Meridian to output SMDR information and connect a serial cable between this port and the PC running NetPBX.

Using the following commands, configure each option as shown below:

 

1. Enable CDR (command: LD 21)

Screenshotmacro
Borderfalse
URL/download/attachments/4817076/avaya_meridian_1.png

2. Port Setup (command: LD 22)

Screenshotmacro

3. CDR Format (commands: LD 22; LD 17)

 

 

HTML
<p>These instructions should assist in configuring your Aastra BP to 
work with TIM Enterprise. If you are not familiar with PBX 
configuration, please contact your system maintainer.</p>

<table class="confluenceTable">
	<tbody>
		<tr>
			<th class="confluenceTh" width=158>Connection information</th>
			<th class="confluenceTh">Description</th>
		</tr>
		<tr>
			<td class="confluenceTd"><b>Connection type</b></td>
			<td class="confluenceTd"><b>Serial Output: </b>
				Avaya Meridian Option Series PBX sends CDR information via a serial connection.
			</td>
		</tr>
		<tr>
			<td class="confluenceTd"><b>Cable configuration</b></td>
			<td class="confluenceTd">Straight-through.
			</td>
		</tr>
	</tbody>
</table>

<h2>Configuring your CDR</h2>

<p>By default, the Avaya Meridian Option CDR output is disabled. You will need to 
speak to your system maintainer to have this enabled. They will need to
 enable CDR output for incoming, outgoing and internal calls. In 
addition to this for incoming calls they will need to enable CLI 
information, DNIS information, response time information and abandoned 
calls.</p>

<p>You will need to configure one of the 'TTY' ports on the Avaya Meridian Option Series to output CDR information. You will then need to connect the serial cable from the 'TTY' port to the PC that NetPBX is installed and 
running on.</p>

<p>The sections below document where to go to. Required entries are highlighted.</p>

<h4>1. Enable CDR (command: LD 21)</h4>

<img class="screenshot naked" src="http://www.tri-line.com/common/img/documentation/tim_enterprise/pbx/avaya_meridian_1.png" alt="Avaya Meridian Option Series" />

<h4>2. Port Setup (command: LD 22)</h4>

<img class="screenshot naked" src="http://www.tri-line.com/common/img/documentation/tim_enterprise/pbx/avaya_meridian_2.png" alt="Avaya Meridian Option Series" />

<h4>3. CDR Format (commands: LD 22; LD 17)</h4>

<img class="screenshot naked" src="http://www.tri-line.com/common/img/documentation/tim_enterprise/pbx/avaya_meridian_3.png" alt="Avaya Meridian Option Series" />

...